Deutsch
English
Français
Walterscheid® Quick adjustable support KU351BT – 8005196
KU351 W=335/30/22 mm-9H
Similar to illustration. Use products only for their intended use. Content is subject to change without notice. Further sizes and combinations may be available: contact us for availability.
Cross references, designation of type by vehicle manufacturers or competitors are for guidance only.
Check that the part is correct for the application before fitting.
The quick adjustable support is suitable for holding height-adjustable couplings in a wide range of detent positions. In addition, it has highly wear-resistant guide rails.
Product advantages
The Walterscheid diamond has been a guarantee of quality and safety for decades.
You can rely on their good reputation. It meets your requirements.
Product advantages
The Walterscheid diamond has been a guarantee of quality and safety for decades.
You can rely on their good reputation. It meets your requirements.
The scope of delivery includes 1x Quick adjustable support KU351BT with single homologation.
If required please use 10 pcs fastening screws 5/8"x1 1/2" 10.9 and 2 pcs fastening screws 3/4" x 1 1/2".
Cut the threaded rod M24x1000 mm 10.9 to 430 mm and fit with M24 washers and nuts.
Adjustable support is suitable for a tractors equipped with a reversible PTO shaft.
Instructions for certificates: Installation of coupling parts must be checked and approved by an recognized expert
according to section 4 of Annex VIIIb to the StVZO based at the information of delivered certificates
All components are designed specifically for the device and performance and it is not allowed to exchange for components other than those prescribed by Walterscheid. Damaged or missing parts can only replace with original Walterscheid parts and retrofit them in accordance with regulations and after consultation with Walterscheid.
The assignment, assembly and use of this model requires a detailed preliminary examination by qualified personnel. It is imperative to check the existing facilities and all of the machinery and equipment for their suitability for attachment. In particular, the characteristic values (e.g. vertical and pulling loads or torques) and the geometries (e.g. dimensions, screw hole patterns, free spaces) must be observed. Depending on the existing equipment of the machine, this can result in the use or purchase of additional components. The content of operating instructions must be observed.
according to section 4 of Annex VIIIb to the StVZO based at the information of delivered certificates
All components are designed specifically for the device and performance and it is not allowed to exchange for components other than those prescribed by Walterscheid. Damaged or missing parts can only replace with original Walterscheid parts and retrofit them in accordance with regulations and after consultation with Walterscheid.
The assignment, assembly and use of this model requires a detailed preliminary examination by qualified personnel. It is imperative to check the existing facilities and all of the machinery and equipment for their suitability for attachment. In particular, the characteristic values (e.g. vertical and pulling loads or torques) and the geometries (e.g. dimensions, screw hole patterns, free spaces) must be observed. Depending on the existing equipment of the machine, this can result in the use or purchase of additional components. The content of operating instructions must be observed.
- Model
- KU351BT
- Type of connection
- modular
- Number of locking positions
- 9
- Vertical load (daN)
- 1400
- Railsize
- W=335/30/22 mm
- D-Value (kN)
- 64,5
- Single homologation
- Single homologation
- Approval
- Single homologation
- AP Code
- L-OL0-SH-0/35
- A (mm)
- 335
- B (mm)
- 30
- C (mm)
- 22
- D1 (mm)
- 222
- E1 (mm)
- 50
- E2 (mm)
- 125
- E3 (mm)
- 345
- AP-Code
- L-OL0-SH-0/35
- Data sheet
- 3.01.385
- Colour
- Black
