Walterscheid® PowerDrive PTO Driveshaft with one-sided wide angle joint PWE 480 - 1800139

Product number: 1800139

PWE 480 SPGF25Z 1210 3583310 358330 S4LGA/S5 ***


Similar to illustration. Use products only for their intended use. Content is subject to change without notice. Further sizes and combinations may be available: contact us for availability.
Cross references, designation of type by vehicle manufacturers or competitors are for guidance only.
Check that the part is correct for the application before fitting.


PowerDrive drive shaft with connection forks and single-sided wide-angle joint

Product advantages

PowerDrive universal drive shafts are specially designed for machines in continuous use and meet the highest requirements. Maintenance is usually carried out only once per season (every 250 hours - depending on application use). These long maintenance intervals are achieved through a number of technologies: The material of the protective bearings requires only minimal lubrication. The joints are equipped with special universal joint seals (multi-lip technology), whose shape and material prevent grease leakage or dust penetration. The profile tubes are optionally equipped with a grease nipple. These tubes are made of specially treated material that reduces sliding forces and minimizes wear on the profile tubes. Profile tube seals wipe off dirt and prevent grease loss. For easy handling of the PowerDrive drive shaft, the guard funnels can be easily unlocked and pushed back. The resulting free space makes it much easier to couple and uncouple the drive shafts and to maintain the joints and protective bearings. All PowerDrive joints are also equipped with bush bottom lubrication. Profiled, thick-walled protective tubes prevent the two protective halves from twisting relative to each other. The retaining chain on the tractor side therefore becomes superfluous. The risk of defects in the guard due to incorrect chain attachment is reduced. With the full guard version, supporting chains can be dispensed with altogether.
The scope of delivery includes a complete drive shaft size PWE480 with connection forks (profile 1 3/8" (6), 1 3/8" (6)), guard, retaining chain(s), operating and assembly instructions incl. declaration of conformity.
This design is suitable for non-axis-parallel use when the simple universal joint is mainly in the extended position and the wide-angle joint is to be angled. Depending on the application, it is recommended that the wide angle joint can be operated up to a maximum angle of 80°. A constant angle during continuous operation of max. 20° should not be exceeded.
All components are designed specifically for the device and performance and it is not allowed to exchange for components other than those prescribed by Walterscheid. Damaged or missing parts can only replace with original Walterscheid parts and retrofit them in accordance with regulations and after consultation with Walterscheid.
The assignment, assembly and use of this model requires a detailed preliminary examination by qualified personnel. It is imperative to check the existing facilities and all of the machinery and equipment for their suitability for attachment. In particular, the characteristic values (e.g. vertical and pulling loads or torques) and the geometries (e.g. dimensions, screw hole patterns, free spaces) must be observed. Depending on the existing equipment of the machine, this can result in the use or purchase of additional components. The content of operating instructions must be observed.
Type
PWE
Size
480
Shaft length (Lz)
1210
Item no. attachment WH-A
133836
Item no. attachment WH-I
133910
Torque of clutch in daNm
0
Rotation speed max. RPM
1000 UPM
Form attachment WH-A
KP1 3/8
Form attachment WH-I
KP1 3/8
Inner profile length
980
Protective colour
Yellow
Cone Type WH-A
RP5
Chain
K
Length of guard tube (inner)
665
SNR cone WH-I
129928
Outer profile length
960
Length of guard tube (outer)
850
Cross seal
P-DICHTUNG
Abbreviation attachment WH-I
ASGE
Profile tube - outer type
S5
Profile tube - inner type
S4LGA
Guard type
SPGF25Z

ass: 22 sim: 0 croo: 0